Services
What we measure — and how precisely
Every service is performed by certified personnel with calibrated instruments and documented reporting.
A
Non-Destructive Testing
UT, ET, MT, PT, VT plus material & coating thickness measurement — defect detection without damaging the component.
01 Ultrasonic Testing (UT) Internal defect detection with high-frequency sound waves — invisible to any other testing method. ✓ Accredited by E.SY.D. — Cert. No. 134 for Testing 02 Eddy Current Testing (ET) Surface and near-surface defects in conductive materials — rapid inspection without disassembly. ✓ Accredited by E.SY.D. — Cert. No. 134 for Testing 03 Magnetic Particle Testing — Fluorescent (MT) Superior sensitivity for surface and near-surface defects in ferromagnetic materials, under UV illumination. ✓ Accredited by E.SY.D. — Cert. No. 134 for Testing 04 Magnetic Particle Testing — Visible (MT) Critical surface crack detection with visible magnetic particles — crankshafts, connecting rods, engine blocks. ✓ Accredited by E.SY.D. — Cert. No. 134 for Testing 05 Dye Penetrant Testing (PT) Surface-breaking defect identification with visible and fluorescent penetrants. ✓ Accredited by E.SY.D. — Cert. No. 134 for Testing 06 Visual Testing (VT) The foundation of NDT inspection — baseline assessment, defect documentation, in-service capability. 07 Coating Thickness Measurement Precision plating and paint verification — compliance with corrosion-protection coating specifications. ✓ Accredited by E.SY.D. — Cert. No. 134 for Testing 08 Material Thickness Measurement (UT) Ultrasonic wall-thickness measurement from one side, with typical accuracy of ±0.01 mm. ✓ Accredited by E.SY.D. — Cert. No. 134 for Testing
B
Precision Alignment & Metrology
1.0 μm laser alignment, straightness, flatness, deflections, dimensional metrology, balancing, grinding, honing, roughness, hardness, white-metal adhesion, bearing loads.
09 Dimensional Measurement Services Precision metrology with high-resolution measurement tools — diameters, surface finish, wear. 10 Laser Alignment Inspection & Alignment Services Alignment inspections and alignment with state-of-the-art laser systems, 1.0 μm accuracy. 11 Straightness Inspection Direct laser straightness measurement — crankshafts, bearing pockets, rudder and hydro-turbine shafts. 12 In Situ Balancing Dynamic balancing of rotating assemblies in the field — no removal required. 13 In Situ Grinding Operations On-site grinding operations — engines, generators, bearings — without transport to a workshop. 14 Honing of Cylinder Liners Precision honing of cylinder liners — correcting wrong machining, delivering within specifications. 15 Deflection Inspection with Special Dial Gauge Crank web deflections on main and auxiliary engines — verifying correct engine mounting and crankshaft straightness. 16 Flatness and Verticality Inspection Laser flatness measurements — engine bedplates, crane bases, heavy machinery foundations. 17 Bearing Load Measurements (Jack-up test) Bearing load measurement by jack-up test — shaft-system alignment verification. 18 Surface Hardness Measurement Systems Portable Leeb hardness testing — heat-treatment validation, failure mapping. ✓ Accredited by E.SY.D. — Cert. No. 134 for Testing 19 White Metal Adhesion Inspection in Plain Bearings Detection of delamination and voids in plain bearings — before the bearing enters service. 20 Surface Roughness Measurements Roughness measurements with Mitutoyo SJ-400 — connecting-rod bearings, crankshaft pins.
C
Diagnostic Services
ISO 18436-2 Cat IV vibration analysis, torque & torsional vibration, noise & acoustic insulation studies, modal analysis & ODS.
21 Vibration Measurements and Analysis Diagnostic services and fault detection, certified to ISO 18436-2 Category IV — the industry's highest. 22 Torque, Torsional Vibration & Torsional Variations Measurements Essential driveline diagnostics — misalignment, coupling wear, resonance, before catastrophic failure. 23 Noise Measurements & Acoustic Insulation Studies Comprehensive acoustic analysis with certified Brüel & Kjær equipment. 24 Modal Analysis & ODS Natural-frequency identification and visualization of how structures actually move in operation (Operating Deflection Shapes).
D
Specialized Services
Underwater inspection, leak & moisture detection, carbon-fiber yachts, welding, crane repairs, hydro plants, construction supervision, 3D printing, fractography.
25 Underwater Crack Detection and Weld Inspection Field inspection — hull plating, weld seams, structural connections — without drydocking. 26 Water Tightness and Leak Detection Ultrasonic leak detection — tanks, compartments, seawater systems — without pressurization or filling. 27 Non-Destructive Moisture Detection Moisture measurement in hardwood, G.R.P. and surfaces — without intruding on the material. 28 Carbon Fiber Yachts Specialized NDT for advanced composites — delamination, cracks, moisture. 29 Welding Services & Inspection Comprehensive weld quality control — from WPS writing to the cap pass. 30 Bridge Crane Repairs Structural bridge-crane repairs with full weld and geometry verification. 31 Hydroelectric Power Plants Works supervision and problem solving — alignment, straightness, vibration on turbines and generators. 32 Construction Project Supervision Quality supervision on large construction projects. 33 Fractography Failure analysis with optical microscopy and SEM. 34 3D Printing 3D printing with a wide range of thermoplastics — from PLA to PC and PA.
Need a certified inspection?
Describe the problem — we reply with a specific method, schedule and cost.